BL Natural Decking Oil

For The Best!
Size
Paint Calculator
This product is not for online sale and can only be purchased from selected stores.
Find a Store
Your Measurements:
Amount Needed:
For the best result we recommend to use {coatAmount} for {productTitle}
Key benefits
  • Excellent penetration and extra low film build
  • Highly translucent, natural matt finish
  • Quick dry - Water wash up
  • Long lasting, mould, UV and weather resistant
  • Easy-to-use and easy-to-maintain
  • Environmentally friendly and non-toxic
  • Microporous allowing the timber to breathe while repelling unwanted moisture
  • Used on bare timber and existing intact finishes
Technical Information
  • Finish N/A
  • Coverage Approx. 10-12m2/Litre
  • Drying Time Dust dry after approx. 20 minutes / tack free after approx. 2 hours.
  • Recoatable Recoat from 2 hours.
  • Thinning Ready for use. When used on a highly absorbent substrates, dilute up to 10% with water.
Product Features
  • Microporous allowing the timber to breathe while repelling unwanted moisture
  • Easy to use
  • Environmentally friendly and non-toxic
  • Water based
  • Fast drying

Product Description

Long-lasting, quick-recoat, easy-to-use and easy-to-maintain, pigmented translucent timber finish developed specially for Australian conditions. Cetol® BL Natural Decking Oil is an extra low build coating that penetrates deeply into the timber to replace natural oils and resins lost through weathering, enhancing its natural beauty. This microporous coating allows the timber to breathe whilst repelling unwanted moisture.

Application Description

Ready to use with no need to thin. Stir thoroughly before use. Final colour will depend upon timber type, previous treatment and the number of coats applied. Ensure timber moisture content is below 15%. Do not apply in temperatures below 5℃ and above 35°C, in damp conditions (when relative humidity is above 85%), or if rain or dew is likely before the product has dried. If using more than one can, it is advisable to mix them together in a larger container or finish in a corner before starting the new can to ensure colour consistency. On previously stained timber, touch up bare areas first and allow to dry. Avoid heavy wear and tear on the decking for a few days after application. At temperatures below 10°C and when used internally with limited air circulation, the drying process will be delayed. On correctly prepared surfaces, two or three coats evenly with a good quality brush along the grain, avoiding overlaps. Allow minimum of 2 hours between coats.

Technical & Safety Documentation

Warning. May cause an allergic skin reaction. Causes serious eye irritation. Keep out of reach of children. If medical advice is needed, have product container or label at hand. Wear protective gloves. Wear eye or face protection. Avoid breathing vapor. Wash hands thoroughly after handling. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air).
Download Adobe Reader

System information

Bare wood- Two (under cover) or three coats of Cetol BL Natural Decking Oil as a standalone finish.

Tips & Advice

  • 1. Preparing the Surfaces
    "Surface Description: Hardwood and softwood decking including Treated Pine, Merbau, Spotted Gum and Jarrah.
    Preparation and application advice:
    Step 1: Ensure the timber to be treated is clean, dry and free from any dirt or loose debris. New Timber: New tannin-rich timbers should be allowed to season first or rough sanded and treated with Sikkens Cetol BL Tannin & Oil Remover to encourage oils and tannins to be drawn to the surface. Older Timber: Sand back to bare all flaking, peeling, and weathered coating. If the existing stain finish is in good condition or the timber has uniformly weathered (turned grey) with no visible finish, then sanding is not essential; move to the next step.
    Step 2: Cean the timber with Sikkens Cetol BL Deck & Wood Cleaner. Rinse and allow to dry thoroughly. For previously stained timber with an intact finish, for best results, light sanding is recommended. Remove sanding dust.
    Step 3: Apply Sikkens Cetol BL Natural Decking Oil
    Stir the can well before and frequently during use.
  • 2. Cleaning
    Clean brushes and equipment immediately with warm water and soap / washing-up liquid.
  • 3. Storing
    Store in accordance with local regulations. Store in original container protected from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10 of the MSDS file) and food and drink. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate containment to avoid environmental contamination.

How much paint do I need?

Measure your dimensions

Do you know the area?

Enter your measurements

Paintable area

{{!-- The value will be injected with JavaScript --}}
{{!-- The value will be injected with JavaScript --}}
m²

More than one wall to paint? Try our advanced paint calculator

Measure the height and length of the surface you want to paint (in metres or centimetres).

Your Measurements:

{{!-- This value will be injected with JavaScript --}}

Amount needed:

{{!-- This value will be injected with JavaScript --}}

This is an estimated based on 2 coats. Actual coverage will depend on the conditions of the surface. If the colour change is strong, more coats may be required.

More than one wall to paint? Try our advanced paint calculator

Add a new job

  • Kitchen
  • Bedroom
  • Living Room

Add a new job

  • Kitchen
  • Bedroom
  • Living Room

Edit job

Delete job

Delete job

Are you sure? All notes, photos and saved items will be deleted.

Save Color

Save to My Workspace

Add to job

BL Natural Decking Oil

Save to My Workspace

Sorry, we couldn't find any results
Fetching the data, please wait...