Deck Ultra Slip Resistant

Deck Ultra Slip Resistant

For The Best!
Size
Paint Calculator
This product is not for online sale and can only be purchased from selected stores.
Find a Store
Your Measurements:
Amount Needed:
For the best result we recommend to use {coatAmount} for {productTitle}
Technical Information
  • Finish Satin Finish
  • Coverage Approx. 8-10m2/Litre
  • Thinning None. Ready for use after thorough stirring. Apply liberally in the direction of the grain using a good quality brush for optimum penetration. DO NOT use rollers or applicators.
  • Composition Alkyd
Product Features
  • Microporous allowing the timber to breathe while repelling unwanted moisture
  • Easy application
  • Oil based
  • Resists blistering, peeling and mould
Deck Ultra Slip Resistant is a durable, easy-to-use, and low-maintenance slip-resistant timber stain. It penetrates deeply into the timber and provides extreme UV and weather protection. The microporous coating allows the timber to breathe while repelling unwanted moisture, making it ideal for decks, steps, walkways wherever slip resistance is required. P4 slip resistance is achieved with two coats.
Ready to use with no need to thin. Stir thoroughly before use. Final colour will depend upon timber type, previous treatment and the number of coats applied. Ensure timber moisture content is below 15%. Do not apply in temperatures below 5℃ and above 35°C, in damp conditions (when relative humidity is above 85%), or if rain or dew is likely before the product has dried. If using more than one can, it is advisable to mix them together in a larger container or finish in a corner before starting the new can to ensure colour consistency. On previously stained decking, touch up bare areas with Sikkens Cetol HLSe and allow to dry before finishing with Sikkens Cetol Deck Slip Resistant. Avoid heavy wear and tear on the decking for a few days after application. At temperatures below 10°C and when used internally with limited air circulation, the drying process will be delayed. On correctly prepared surfaces, apply two coats evenly with a quality brush along the grain, avoiding overlaps. Allow 24 hours between coats.
Flammable liquid and vapour. May cause an allergic skin reaction.  May cause cancer. Suspected of damaging fertility or the unborn child. Harmful to aquatic life with long lasting effects.  
Read label before use. Keep out of reach of children. If medical advice is needed, have product container or label at hand. Do not apply directly into or onto water. Take all reasonable steps to ensure that the substance does not cause any
significant adverse effects to the environment beyond the application area. Obtain special instructions before use. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Wear protective gloves, protective clothing, eye protection, face protection, or hearing protection.  Avoid release to the environment. Avoid breathing vapor
IF exposed or concerned- Get medical advice or attention. Take off contaminated clothing and wash it before reuse. IF ON SKIN- Wash with plenty of water. If skin irritation or rash occurs- Get medical advice or attention. Store locked up. Store in a well-ventilated place. Keep cool. Dispose of contents and container in accordance with all local, regional, national or international regulations. Contains Naphtha (petroleum), hydrotreated heavy ≥30 - ≤65%, Naphtha (petroleum), hydrodesulfurized heavy ≤10%,  (2-methoxymethylethoxy)propanol ≤3%, Xylene ≤3%, 2-ethylhexanoic acid, zirconium salt ≤1, IPBC ≤0.82%, neodecanoic acid, cobalt salt <1%, 2-butanone oxime <1%.
. Avoid the inhalation of dust. Wear suitable face mask if dry sanding. Special precautions should be taken during surface preparation of pre-1990s paint surfaces over wood and metal as they may contain harmful lead.
Additional information is listed in the Safety Data Sheet.
Download Adobe Reader
Bare wood- a priming coat of HLSe followed by two coats of Deck Ultra Slip Resistant. For subsequent maintenance- one or two coats of Cetol Deck Slip Resistant.
  • 1. Preparing the Surfaces
    For new timber (including timber with mill glaze): New or unseasoned hardwoods such as Merbau, Spotted Gum, Tallowwood, Jarrah, and Ironbark contain natural tannins. These tannins must be extracted before coating. This will occur naturally over 3 to 6 months, depending on exposure, or the process can be accelerated using BL Tannin & Oil Remover followed by BL Deck & Wood Cleaner. For best results:
    1. Sand timber using coarse 60–80 grit sandpaper, or softwood using 100–120 grit sandpaper, in the direction of the grain. Sanding improvs
    adhesion, enhances penetration, and increases durability.
    2. For unseasoned hardwoods: apply BL Tannin & Oil Remover and then BL Deck & Wood Cleaner according to the instructions.
    3. For softwoods or seasoned hardwoods: apply only BL Deck & Wood Cleaner according to the instructions.
    4. Rinse timber thoroughly and allow to dry completely before applying Sikkens Deck Ultra Slip Resistant.
  • 2. After use
    Clean brushes and equipment immediately after use with mineral turpentine/white spirit.
  • 3. Storing
    Store in a well-ventilated place. Keep cool.Store in accordance with local regulations. Store in a segregated and approved area. Store in original container protected from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Eliminate all ignition sources. Separate from oxidising materials. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabelled containers. Use appropriate containment to avoid environmental contamination. See Section 10 for incompatible materials before handling or use.

How much paint do I need?

Measure your dimensions

Do you know the area?

Enter your measurements

Paintable area

{{!-- The value will be injected with JavaScript --}}
{{!-- The value will be injected with JavaScript --}}
m²

More than one wall to paint? Try our advanced paint calculator

Measure the height and length of the surface you want to paint (in metres or centimetres).

Your Measurements:

{{!-- This value will be injected with JavaScript --}}

Amount needed:

{{!-- This value will be injected with JavaScript --}}

Actual coverage will depend on the conditions of the surface. If the colour change is strong, more coats may be required.

More than one wall to paint? Try our advanced paint calculator

Add a new job

  • Kitchen
  • Bedroom
  • Living Room

Add a new job

  • Kitchen
  • Bedroom
  • Living Room

Edit job

Delete job

Delete job

Are you sure? All notes, photos and saved items will be deleted.

Save Color

Save to My Workspace

Add to job

Deck Ultra Slip Resistant

Save to My Workspace

Sorry, we couldn't find any results
Fetching the data, please wait...